Barco EN41 Standard Zoom Long-Throw Projector Lens: Compatible with CRWQ-72B, F70-4K4, F70-4K6

Barco Original Lens EN41 Standard Zoom is a genuine optical accessory for Barco installation projectors, belonging to the long throw category, with a throw ratio of 1.70-2.50:1. The original compatibility list covers 16 models; before installation, simply verify against the projector model and panel size — no adapter rings needed. The value of an original lens isn't a few extra rows of numbers on a spec sheet, but that it is calibrated at the factory to the optical path and mount of that series' chassis: once mounted, the image circle, edge illumination, and focus travel are all at their design values, with no need to compensate image quality via keystone correction.

1. Lens Specifications

Brand	Barco
Lens Model	EN41 Standard Zoom
Throw Ratio	1.70-2.50:1
Product Type	Long Throw
Compatible Models	16
Warranty	12 months; after-sales service available for non-human damage, based on the date on the shipping document

The above specifications are subject to the original manufacturer's specifications. For mechanical dimensions, flange focal distance, and mount type not shown in the spec table, please verify with us against the projector model — ordering based on model similarity alone carries the risk of incompatibility.

2. Converting Throw Ratio to Installation Distance

Throw ratio is the ratio of installation distance to image width. This original lens is a zoom lens (1.70-2.50:1), so the same image size corresponds to a range of distances; as long as installation falls within this range, focus can be achieved.

Image Size	Image Width	Required Installation Distance
100 inches	2.15 m	Approx. 3.65 – 5.38 m
120 inches	2.58 m	Approx. 4.39 – 6.45 m
150 inches	3.22 m	Approx. 5.48 – 8.06 m
200 inches	4.30 m	Approx. 7.31 – 10.75 m

The above figures are the clear distance from the lens face to the screen, excluding rear ventilation and cabling space behind the chassis. Calculated at 16:10 aspect ratio; actual values are subject to on-site measurement and the original manufacturer's manual.

Image quality differs at the two ends of the zoom range: toward the near end the image is brighter with slightly softer edges; toward the far end the edges are sharper with slightly reduced brightness. Where space permits, it is recommended to land in the middle of the range; after installation, first find the sharpest position on the focus ring, then fine-tune the shift.

3. Compatible Models (16)

The table below is taken from the original compatibility list; brightness and resolution are back-filled from the model database, with "—" where unavailable — no speculation.

Model	Brightness	Resolution
CRWQ-72B	7000 lumens	2560x1600
F70-4K4	—	2560x1600
F70-4K6	5400 lumens	2560x1600
F70-4K8	—	2560x1600
F80-4K12	10400 lumens	2716x1600
F90-4K13	—	2560x1600
FL40-4K	3000 lumens	2560x1600
FL40-4K MKII	3000 lumens	2560x1600
FL40-WU	3200 lumens	1920x1200
FL40-WU MKII	3200 lumens	1920x1200
FS40-4K	3000 lumens	2560x1600
FS40-4K MKII	3000 lumens	2560x1600
FS40-WU	3200 lumens	1920x1200
FS40-WU MKII	3200 lumens	1920x1200
FS70-4K4	—	2560x1600
FS70-4K6	5400 lumens	2560x1600

For models outside the list, please send us photos of the projector nameplate and the existing lens for verification — same-generation platforms often share mounts, but ordering based on model similarity is a risk not worth taking.

Throw Ratios Across Model Series

The same EN41 Standard Zoom mounted on the following series does not carry the same nominal throw ratio; selection must use the value for the actual series of the chassis.

Model Series	Throw Ratio
—	1.70-2.50:1

4. Three Things to Confirm Before Replacement

• Confirm the chassis chip and resolution. Original lenses are designed for specific panel sizes; with a different panel specification, the image circle cannot cover it, resulting in vignetting or edge light falloff after installation.
• Calculate the installation distance first. This lens has a nominal throw ratio of 1.70-2.50:1; apply it to your venue dimensions using the table in Section 2. Prime lenses have no margin, and even zoom lenses should leave 10–20 cm at both ends.
• Verify the mount and locking. Original lenses are calibrated to the mount of that series' chassis; after installation, you must hear the lock engage. Image skew and soft edges are mostly due to incomplete locking, not a problem with the lens itself.

If unsure, take a photo of the projector nameplate and the existing lens nameplate and send them to us — verification against the actual hardware is the safest approach.