Vivitek LNS-5STZ Short Zoom Standard Throw Projector Lens: DU5671 DU7090Z DU7295Z-BK DU7295Z-WH

Vivitek Original Lens LNS-5STZ Short Zoom is a genuine optical accessory for Vivitek engineering projectors. It belongs to the standard throw category, with a throw ratio of 1.10-1.30:1, and is designed for DU/DW/DX engineering series panels. The factory compatibility list covers 5 projector models; before installation, simply verify against the projector model and panel size—no adapter rings needed. The value of an original lens isn't about extra rows of numbers in the spec sheet, but that it is calibrated at the factory to match the optical path and bayonet of that series: once mounted, the image circle, edge illumination, and focus travel all match design values, so you don't need keystone correction to compensate for image quality.

1. Lens Specifications

Brand	Vivitek (Vivitek)
Lens Model	LNS-5STZ Short Zoom
Throw Ratio	1.10-1.30:1
Product Type	Standard Throw
Compatible Panel	DU/DW/DX engineering series inch
Covered Models	5 units
Warranty	12 months; non-human damage eligible for after-sales service, based on the date on the shipping document

The above specifications are subject to the original factory specifications. For mechanical dimensions, flange focal distance, and bayonet type not shown in the spec table, please verify with us against your projector model—ordering based on similar model numbers carries the risk of incompatibility.

2. Converting Throw Ratio to Installation Distance

Throw ratio is the ratio of installation distance to image width. This original lens is a zoom lens (1.10-1.30:1), so the same image size corresponds to a range of distances; as long as installation falls within this range, focus can be achieved.

Image Size	Image Width	Required Installation Distance
100 inch	2.15 m	Approx. 2.37 – 2.79 m
120 inch	2.58 m	Approx. 2.84 – 3.35 m
150 inch	3.22 m	Approx. 3.55 – 4.19 m
200 inch	4.30 m	Approx. 4.73 – 5.59 m

The above figures are the net distance from the lens front to the screen, excluding rear ventilation and cabling space. Calculated for 16:10 aspect ratio; actual values are subject to on-site measurement and the original manual.

Image quality differs at the two ends of the zoom range: toward the near end the image is brighter with slightly softer edges; toward the far end the edges are sharper with slightly reduced brightness. Where space permits, we recommend positioning in the middle of the range; after installation, first find the sharpest point on the focus ring, then fine-tune the shift.

3. Compatible Models (5 units)

The table below is taken from the original factory compatibility list; brightness and resolution are filled in from the model database, with "—" where unavailable—no speculation.

Model	Brightness	Resolution
DU5671	6200 lumens	1920x1200
DU7090Z	6000 lumens	1920x1200
DU7295Z-BK	9000 lumens	1920x1200
DU7295Z-WH	9000 lumens	1920x1200
H5095	2000 lumens	1920x1080

For models not on the list, please send us photos of the projector nameplate and the existing lens for verification—same-generation platforms often share bayonets, but ordering based on similar model numbers isn't worth the risk.

Throw Ratios Across Model Series

The same LNS-5STZ Short Zoom mounted on the following series has different nominal throw ratios; selection should be based on the actual series of your projector.

Model Series	Throw Ratio
—	1.10-1.30:1

4. Three Things to Confirm Before Replacement

• Panel size must match. The LNS-5STZ Short Zoom is designed for DU/DW/DX engineering series inch panels. For projectors with different panel sizes or resolutions, even if the bayonet fits, the image circle and edge illumination will be problematic.
• Calculate installation distance first. This lens has a nominal throw ratio of 1.10-1.30:1; use the table in Section 2 to map to your venue dimensions. Prime lenses have no margin, and even zoom lenses need 10–20 cm clearance at both ends.
• Verify bayonet and locking. The original lens is calibrated to the bayonet of that series; after mounting, you must hear it lock into place. Image skew or soft edges are usually due to incomplete locking, not a problem with the lens itself.

If unsure, take a photo of the projector nameplate and the existing lens nameplate and send them to us—verification against the actual hardware is the safest approach.