Christie OEM Lens 144-111014-XX Fixed is an original optical accessory for Christie engineering projectors. It is a standard throw lens (Standard Throw) with a 0.90:1 throw ratio. The official model compatibility list covers 16 models. Before installation, simply verify the projector model and panel size; there is no need to make do with adapter rings. The value of an OEM lens lies not in the extra figures it adds to a specification sheet, but in the fact that it is calibrated at the factory to the optical path and lens mount of that projector series. Once installed, the image circle, edge illumination, and focusing travel are all at their design values, so there is no need to use keystone correction to compensate for image quality.
I. Lens Specifications
| Brand | Christie (Christie) |
| Lens Model | 144-111014-XX Fixed |
| Throw Ratio | 0.90:1 |
| Product Type | Standard throw (Standard Throw) |
| Compatible Projector Models | 16 units |
| Warranty | 12 months; after-sales service is available for damage not caused by the user, based on the date on the shipping documents |
The above specifications are based on the manufacturer's official specifications. For mechanical dimensions, flange distance, and mount type not listed in the specifications table, please contact us with your projector model for verification. Ordering solely on the basis of a similar model carries the risk that the lens will not fit.
II. Calculating Installation Distance from Throw Ratio
The throw ratio is the ratio of the installation distance to the image width. This OEM lens has a fixed focal length (0.90:1), so the installation distance varies linearly with image size and offers no adjustment margin. Accurate measurements are essential before installation.
| Image Size | Image Width | Required Installation Distance |
|---|---|---|
| 100 inches | 2.15 m | approx. 1.94 m |
| 120 inches | 2.58 m | approx. 2.32 m |
| 150 inches | 3.22 m | approx. 2.90 m |
| 200 inches | 4.30 m | approx. 3.87 m |
These figures represent the clear distance from the front surface of the lens to the screen and do not account for rear housing ventilation and cable-management clearance. They are calculated for a 16:10 image; actual values are subject to on-site measurements and the manufacturer's manual.
III. Compatible Projector Models (16 Units)
The following table is taken from the official model compatibility list. Brightness and resolution have been populated from the model database; where the data is unavailable, “—” is shown rather than making estimates.
| Model | Brightness | Resolution |
|---|---|---|
| Boxer 2K20 | — | — |
| Boxer 2K25 | — | — |
| Boxer 2K30 | — | — |
| Boxer 30 | — | — |
| Boxer 4K20 | — | — |
| Boxer 4K30 | — | — |
| D4K40-RGB | 40000 lumens | 4096x2160 |
| Eclipse G3 | — | — |
| Griffyn 4K32-RGB | — | — |
| Griffyn 4K35-RGB | — | — |
| Griffyn 4K50-RGB | — | — |
| Mirage 304K | — | — |
| Mirage 4K40-RGB | — | — |
| Mirage SST | — | — |
| Roadie 4K40-RGB | — | — |
| Sapphire 4K40-RGBH | — | — |
To determine whether a model not on the list is compatible, send us photos of the projector nameplate and the current lens. Platforms from the same generation often share the same lens mount, but ordering based solely on a similar model name is not worth the risk.
Throw Ratios by Projector Series
The nominal throw ratio of the same 144-111014-XX Fixed lens varies by projector series. Select the value that corresponds to the series of your actual projector.
| Projector Series | Throw Ratio |
|---|---|
| — | 0.90:1 |
IV. Three Checks Before Replacement
- Confirm the projector's imaging chip and resolution.OEM lenses are designed for a specific panel size. If the panel specifications differ, the image circle cannot cover the full image, resulting in vignetting or light loss at the edges after installation.
- Calculate the installation distance first.This lens has a rated throw ratio of 0.90:1. Use the table in Section II to calculate the distance for your installation site. A fixed-focus lens offers no adjustment margin; even with a zoom lens, allow an additional 10–20 cm at both ends.
- Verify the lens mount and locking mechanism.The OEM lens is calibrated to the mount used on that projector series. After installation, you must hear the lens click into the locked position. A skewed image and soft edges are usually caused by incomplete locking, not by the lens itself.
If you are unsure, send us one photo each of the projector nameplate and the existing lens nameplate. Physical verification is the safest approach.
Project Consultation
For OEM lens selection, project configuration recommendations, or a complete model compatibility list for the Zorsika 144-111014-XX Fixed, contact us using the following details:
| Contact Phone | 0086-20-38551187 |
| sales@zorsika.com | |
| Business Hours: Monday to Friday 9:00-18:00 | |
The lens model, OEM part number, and compatible projector models in this article are sourced from the official model compatibility list and the Zorsika product database. The data is continually updated; actual quotations are subject to confirmation.
