Vivitek 5811119237-SVV Long Zoom 1 Telephoto Projector Lens: Compatible with DU7095Z-BK

Vivitek Original Lens 5811119237-SVV Long Zoom 1 is a genuine optical accessory for Vivitek engineering projectors. It is a long-throw lens with a throw ratio of 1.93-2.90:1, designed for DU/DW/DX engineering series panels. The original compatibility list covers 7 models; before installation, simply verify against the projector model and panel size — no adapter rings needed. The value of an original lens isn't a few extra rows of numbers on a spec sheet, but that it is calibrated at the factory to the optical path and mount of that series: once installed, the image circle, edge illumination, and focus travel are all at their design values, with no need to compensate image quality using keystone correction.

1. Lens Specifications

Brand	Vivitek
Lens Model	5811119237-SVV Long Zoom 1
Throw Ratio	1.93-2.90:1
Product Type	Long Throw
Compatible Panel	DU/DW/DX engineering series inch
Covered Models	7
Warranty	12 months; non-human damage is eligible for after-sales service, based on the date on the shipping document

The above specifications are subject to the original manufacturer's specifications. For mechanical dimensions, flange focal distance, and mount type not shown in the spec table, please verify with us against your projector model — ordering based on model similarity alone carries the risk of incompatibility.

2. Converting Throw Ratio to Installation Distance

Throw ratio is the ratio of installation distance to image width. This original lens is a zoom lens (1.93-2.90:1), so the same image size corresponds to a range of distances; as long as installation falls within this range, focus can be achieved.

Image Size	Image Width	Required Installation Distance
100 inch	2.15 m	Approx. 4.15 – 6.23 m
120 inch	2.58 m	Approx. 4.98 – 7.48 m
150 inch	3.22 m	Approx. 6.22 – 9.35 m
200 inch	4.30 m	Approx. 8.30 – 12.47 m

The above figures are the clear distance from the lens face to the screen, excluding rear ventilation and cabling space behind the projector body. Calculated for a 16:10 aspect ratio; actual values are subject to on-site measurement and the original manufacturer's manual.

Image quality differs at the two ends of the zoom range: toward the near end the image is brighter with slightly softer edges; toward the far end the edges are sharper with slightly reduced brightness. Where space permits, it is recommended to land in the middle of the range; after installation, first find the sharpest position on the focus ring, then fine-tune the shift.

3. Compatible Models (7)

The table below is taken from the original compatibility list; brightness and resolution are filled in from the model database, with "—" where unavailable, without speculation.

Model	Brightness	Resolution
DU7095Z-BK	6500 lumens	1920x1200
DU7095Z-WH	6500 lumens	1920x1200
DU7098Z-BK	7000 lumens	1920x1200
DU7098Z-WH	7000 lumens	1920x1200
DU7195Z	8000 lumens	1920x1200
DU7295Z-BK	9000 lumens	1920x1200
DU7295Z-WH	9000 lumens	1920x1200

To determine whether models outside the list are compatible, please send us photos of the projector nameplate and the existing lens for verification — same-generation platforms often share mounts, but the risk of ordering based on model similarity isn't worth it.

Throw Ratios Across Model Series

The same 5811119237-SVV Long Zoom 1 installed on the following series has different nominal throw ratios; selection should be based on the actual series of your projector.

Model Series	Throw Ratio
—	1.93-2.90:1

4. Three Things to Confirm Before Replacement

• Panel size must match. The 5811119237-SVV Long Zoom 1 is designed for DU/DW/DX engineering series inch panels. Projectors with different panel sizes or resolutions may have image circle and edge illumination issues even if the mount fits.
• Calculate installation distance first. This lens has a nominal throw ratio of 1.93-2.90:1; apply the table in Section 2 to your venue dimensions. Prime lenses have no margin, and even with zoom you should allow 10–20 cm at both ends.
• Verify the mount and locking. The original lens is calibrated to the mount of that series; after installation you must hear it lock into place. Image skew or soft edges are usually due to incomplete locking, not a problem with the lens itself.

If unsure, take a photo of the projector nameplate and the existing lens nameplate and send them to us — verification against the actual hardware is the safest approach.