Barco EN67 Super Wide Fixed Short Throw Projector Lens: Compatible with 14 Models Including Balder

Barco Original Lens EN67 Super Wide Fixed is a genuine OEM optical accessory for Barco installation projectors, belonging to the short throw category, with a throw ratio of 0.65:1. The original compatibility list covers 14 projector models; before installation, simply verify against the projector model and panel size — no adapter rings needed. The value of an original lens isn't about a few extra rows of numbers in the spec sheet, but that it is calibrated at the factory to the optical path and lens mount of that projector series: once mounted, the image circle, edge illumination, and focus travel all match design values, so you don't need keystone correction to compensate for image quality.

1. Lens Specifications

Brand	Barco
Lens Model	EN67 Super Wide Fixed
Throw Ratio	0.65:1
Product Type	Short Throw
Compatible Models	14
Warranty	12 months; after-sales service available for non-human damage, based on the date on the shipping document

The above specifications are subject to the original manufacturer's specifications. For mechanical dimensions, flange focal distance, and mount type not shown in the spec table, please verify with us against your projector model — ordering based on model similarity alone carries the risk of incompatibility.

2. Throw Ratio and Installation Distance Calculation

The throw ratio is the ratio of installation distance to image width. This original lens is fixed focal length (0.65:1), so the installation distance changes linearly with image size with no adjustment margin — it must be measured accurately before installation.

Image Size	Image Width	Required Installation Distance
100 inches	2.15 m	Approx. 1.40 m
120 inches	2.58 m	Approx. 1.68 m
150 inches	3.22 m	Approx. 2.10 m
200 inches	4.30 m	Approx. 2.79 m

The above figures are the clear distance from the lens front to the screen, excluding rear ventilation and cabling space behind the projector. Calculated for 16:10 aspect ratio; actual values are subject to on-site measurement and the original manufacturer's manual.

3. Compatible Models (14)

The table below is taken from the original manufacturer's compatibility list; brightness and resolution are filled in from the model database, with "—" where unavailable, without speculation.

Model	Brightness	Resolution
Balder	7000 lumens	3840x2160
Balder CinemaScope	7000 lumens	3840x2160
Bragi	2600 lumens	3840x2160
Bragi CinemaScope	2600 lumens	3840x2160
F400-4K	5400 lumens	2560x1600
F400-N4K	5000 lumens	4096x2160
FS400-4K	5400 lumens	2560x1600
FS400-N4K	5000 lumens	4096x2160
Heimdall	4500 lumens	4096x2160
Heimdall Cinemascope	4500 lumens	4096x2160
Heimdall+	4500 lumens	4096x2160
Heimdall+ Cinemascope	4500 lumens	4096x2160
Loki	12000 lumens	3840x2160
Loki CinemaScope	12000 lumens	3840x2160

For models not on the list, please send us a photo of the projector nameplate and the existing lens for verification — same-generation platforms often share the same mount, but ordering based on model similarity alone is a risk not worth taking.

Throw Ratios Across Model Series

The same EN67 Super Wide Fixed lens, when mounted on the following series, does not have the same nominal throw ratio — selection should be based on the actual series of your projector.

Model Series	Throw Ratio
—	0.65:1

4. Three Things to Confirm Before Replacement

• Confirm the projector chip and resolution. The original lens is designed for a specific panel size; if the panel specifications differ, the image circle cannot cover it, resulting in vignetting or edge light loss after installation.
• Calculate the installation distance first. This lens has a nominal throw ratio of 0.65:1; apply it to your venue dimensions using the table in Section 2. Fixed focal length has no margin; even for zoom lenses, leave 10–20 cm at both ends.
• Verify the mount and locking. The original lens is calibrated to the lens mount of that projector series; after installation, you must hear the lock engage. Image skew or soft edges are mostly due to incomplete locking, not a problem with the lens itself.

If unsure, take a photo of the projector nameplate and the existing lens nameplate and send them to us — verification against the actual hardware is the most reliable approach.